R&D

—R&D

Electronics R&D And

Testing Laboratory

In Greater Noida

 Ionotronics runs an in-house R&D testing lab at its Greater Noida facility. With 16 instruments covering optical, electrical, safety, thermal and battery testing, the team checks product performance, reliability and standards alignment before products move into production. The lab supports customers across India.

Innovate.

Validate.

Ensure Quality.

STATS STRIP

16

Test and measurement instruments

5

Test areas

7 kv

Surge tester rating

−40°C to +150°C

Environment chamber range

RT to 300°C

Hot air oven range

Why Testing Matters At Ionotronics

Testing is the backbone of R&D. It confirms that products are reliable and safe, checked against the applicable standards, high performing and ready for the market.

Key objectives

Our purpose: To ensure that our machines, products and solutions meet performance, reliability and compliance requirements through systematic testing and validation.

Four cards

Our R&D Testing Workflow

01

Requirement and test plan

Identify the product, sample revision, intended use, applicable standard and acceptance criteria.

02

Setup and calibration

Select instruments, verify calibration status, and prepare fixtures, wiring, environment and safety controls.

03

Execute tests

Run tests in an approved sequence and capture readings, settings, observations and deviations.

04

Analyse results

Check accuracy, repeatability, trends and pass or fail status against the approved criteria.

05

Report and approve

 Document findings, log non-conformities, define corrective action, and approve retest or release.

Control gate

Testing does not proceed until setup, calibration, safety checks and acceptance criteria are complete.

Standards strip

Tests are planned against LM-79, LM-80, IEC and BIS requirements, ISO references and customer specifications, as applicable to each product.

Key test areas

Five Test Areas, One Lab

IMG_4836
 luminous intensity, flux and efficacy, beam angle and spatial distribution, CCT and CRI. Uses the goniophotometers and the AC power analyser.
IMG_4841
voltage, current, power, harmonics, waveforms and component values. Uses the AC power analyser, oscilloscope, function generator, LCR meter, DC supply and DC load.
IMG_4860
surge withstand, breakdown voltage, leakage current, voltage dips and interruptions, recovery time. Uses the surge tester and the dips and interruption tester.
WhatsApp Image 2026-10-05 at 3.10.48 PM
temperature and humidity exposure, thermal stability and long-term stability. Uses the hot air oven, the environment chamber and the temperature recorder.
WhatsApp Image 2026-10-05 at 3.10.47 PM
internal resistance, open-circuit voltage and endurance checks on battery cells. Uses the intelligent battery IR tester.
RESEARCH & DEVELOPMENT

Test Equipment in Our R&D Lab

Our R&D laboratory is equipped with precision instruments for photometric analysis, electrical testing, power measurement and environmental validation.

16 Testing Instruments
04 Equipment Categories
360° Testing Capabilities
◉
01 / OPTICAL TESTING

Photometric & Optical Analysis

03
01

Everfine Goniophotometry Machine (YF1000)

Maps spatial luminous intensity distribution and total luminous flux through precise angular rotation. Reports luminous intensity, beam angle and CIE colour parameters.

02

Everfine LED Goniophotometer (LED626)

Measures angular colour uniformity, lumen output and spatial light distribution of LED packages and modules, including beam angle, CCT and CRI.

03

4X Optical Microscope

Enables micro-level inspection of solder joints, PCB tracks, wire bonds, component placement and surface defects.

⌁
02 / ELECTRICAL TESTING

Signals & Immunity

04
04

Everfine Surge Tester (7 kV)

Applies high-voltage transient surges to evaluate withstand against lightning and industrial switching events, including breakdown voltage and leakage current.

05

Everfine Voltage Dips And Interruption Tester

Simulates supply dropouts and brownouts to evaluate product behaviour, recovery time and performance criteria.

06

Owon Metro Digital Oscilloscope

Captures waveforms, transients, timing, ripple, rise time and jitter with real-time digital analysis.

07

Sigma Function Generator

Injects controlled sine, square and ramp waveforms to evaluate frequency response, waveform accuracy and distortion (THD).

ϟ
03 / POWER TESTING

Power, Source & Component Measurement

06
08

AC Power Analyser

Measures true RMS voltage, current, power, power factor, frequency and harmonic distortion (THD).

09

Dual-Channel DC Regulated Power Supply

0 to 30 V / 0 to 3 A

Provides stable, low-noise supply rails for controlled functional testing.

10

UNI-T DC Electronic Load

Up to 150 V / 40 A / 400 W

Programmable load for testing output regulation, efficiency, power adapters and battery discharge behaviour.

11

Scientific LCR Meter

Measures inductance, capacitance, resistance and Q factor of electronic components.

12

Intelligent Battery IR Tester

Measures internal resistance and open-circuit voltage of battery cells to identify degraded units and track battery health trends.

13

Rishabh Multimeter

Performs AC and DC voltage, current, resistance and continuity checks.

♨
04 / ENVIRONMENTAL TESTING

Thermal & Environmental

03
14

Lutron 12-Channel Temperature Recorder

Records multiple temperature points simultaneously using thermocouple sensors for thermal monitoring.

15

Sharadatronics Hot Air Oven

Room Temperature to 300°C

Provides sustained high-temperature stress for ageing and material stability checks.

16

KELVIRON Environment Chamber

−40°C to +150°C | 10% to 98% RH

Performs temperature and humidity cycling for environmental and product stability testing.

Ionotronics R&D Testing Laboratory
IONOTRONICS R&D

Precision Testing & Quality Validation

Advanced laboratory equipment for reliable product performance.

✓

Precision testing. Reliable measurements. Confidence in every product.

QUALITY & VALIDATION

Machine-Wise Testing Plan

Each instrument supports specific testing activities to verify product performance, electrical characteristics and environmental reliability against applicable standards.

# Instrument What it tests Reference
01 Everfine YF1000 Goniophotometry Machine Luminous intensity, beam angle, flux, CIE colour parameters LM-79
02 Everfine LED626 LED Goniophotometer Flux, CCT, CRI, spatial distribution LM-79
03 Sigma Function Generator Frequency, waveform, distortion Per test plan
04 Owon Metro Oscilloscope Signal analysis, rise time, jitter, harmonics Per test plan
05 Everfine Surge Tester (7 kV) Surge withstand, breakdown voltage, leakage current IEC 61000-4-5
06 Everfine Voltage Dips and Interruption Tester Dip and interruption response, recovery IEC 61000-4-11
07 AC Power Analyser Power quality, power factor, THD, harmonics IEC 61000 series
08 DC Regulated Power Supply Voltage and current stability Product specification
09 UNI-T DC Electronic Load Load response, efficiency, regulation Product specification
10 Scientific LCR Meter R, L, C, Q factor Component specification
11 Intelligent Battery IR Tester Internal resistance, open-circuit voltage IEC 61960
12 Rishabh Multimeter Voltage, current, resistance, continuity Per test plan
13 4X Optical Microscope Visual inspection of solder joints, tracks, workmanship Customer workmanship criteria
14 Lutron 12-Channel Temperature Recorder Multi-point temperature logging Per test profile
15 Sharadatronics Hot Air Oven Thermal stability, ageing IEC 60068-2 series
16 KELVIRON Environment Chamber Temperature, humidity, performance IEC 60068-2 series
i

Test levels and limits come from the product specification and the applicable standard. Instrument ratings are capability figures, not acceptance levels.

TESTING METHODOLOGY

How A Typical Test Runs

Every product goes through a structured testing process to evaluate performance, electrical reliability and environmental stability.

01
☼
PHOTOMETRIC TESTING

LED Performance Test

Evaluate light output and colour characteristics against product specifications.

01

Set Up & Calibrate

Prepare and calibrate the instrument.

02

Measure Luminous Flux

Measure total luminous output.

03

Verify CCT & CRI

Check colour temperature and rendering.

04

Compare Results

Compare against product specifications.

02
ϟ
ELECTRICAL TESTING

Electrical Stress Test

Assess product response to electrical surges and supply voltage disturbances.

01

Apply Surge or Dip

Apply the specified electrical disturbance.

02

Monitor Response

Observe product behaviour during testing.

03

Verify No Damage

Check the product condition after testing.

03
♨
ENVIRONMENTAL TESTING

Thermal Test

Evaluate product performance and stability under controlled temperature conditions.

01

Set Temperature Profile

Configure the required temperature conditions.

02

Monitor Performance

Observe product operation during testing.

03

Validate Stability

Evaluate stability under test conditions.

✓

Structured testing. Consistent evaluation. Reliable product validation.

WhatsApp Image 2026-10-05 at 3.10.48 PM

Data Analysis, Traceability and Reporting

Every test produces evidence that can be reviewed, repeated and audited.

Flow: Data storage → Traceability → Test report

A test record captures: product and revision, sample ID, test standard or clause, instrument ID and calibration status, setup and settings, raw readings, acceptance limit, result and reviewer approval.

Outcomes and benefits

What Testing Delivers

Closing line: Quality builds trust.

Testing Backed by Our Manufacturing Facilities

Our lab sits next to production in Greater Noida, so test findings reach the team building your product.

Untitled Design (1)

FAQ

Frequently Asked Questions

What testing does the Ionotronics R&D lab carry out?

The lab covers optical and photometric testing, electrical and power testing, surge and voltage dip testing, thermal and environmental testing, and battery cell assessment. Test scope is agreed for each product.

Which instruments are available in the lab?

The lab has 16 instruments, including Everfine goniophotometers, a 7 kV surge tester, a voltage dips and interruption tester, an oscilloscope, a function generator, an AC power analyser, a DC supply and electronic load, an LCR meter, a battery IR tester, a hot air oven and an environment chamber.

Which standards do you test against?

Tests are planned against the standard or customer specification that applies to the product, for example LM-79 and LM-80 for LED products, IEC 61000-4-5 for surge, IEC 61000-4-11 for voltage dips, and BIS requirements where relevant.

Can you test LED products?

Yes. LED and luminaire testing includes luminous flux, beam angle, spatial distribution, CCT and CRI on the goniophotometers, plus electrical and thermal checks.

Do you offer testing only, for products made elsewhere?

R&D testing mainly supports products built at Ionotronics. For a testing-only requirement, share your product, the standard and the tests you need, and the team will confirm what can be done.

Do you test batteries?

The lab can measure battery cell internal resistance and open-circuit voltage. Ionotronics does not manufacture batteries; see the battery management services page for that offering.

Planning a Product Validation or Testing Project?

Share your product, specification and the tests you need. The Ionotronics team will review your requirement and suggest next steps. Serving customers across India from Greater Noida.

Call 0120-4453700 or email Info@ionotronics.in

Go Back Top
Call Now Button